Release Notes for laserscore10m.application
Version 2026.3.2
Bug
- #47946 : Fix device staying disconnected for 10 min after network interruption under certain circumstances
Version 2026.3.1
Bug
- #47920 : Production Test robustness
- #47927 : Increase Themelia data reliability after network interruptions
Version 2026.3.0
Bug
- #46350 : Reliability of inhouse system check 'FrameHitTest' improved
- #46365 : Prevent duplicate GUIDs from being generated
Feature
- #43184 : Add MeasurementsStartCount to RawData
- #45683 : Support AirRifle / AirPistol TargetChanger AddOn LS10G3AN006
- #46594 : Support locking of Didrom subcomponents during production
Task
- #39052 : New Blink Code for Error LED when device is not 'Operational' (5x)
- #42886 : Increased and unified voltage tolerances for production tests (PowerSupplyTest)
- #47811 : Subcomponent update (Master FPGA) to Version 1.9.0
Version 2026.2.0
Bug
- #43800 : Prevent incoming mqtt message drop during startup
- #45019 : Subcomponent software versions are now updated on every request instead of only at startup
- #45255 : Adjustments / Shotprocessing can be disabled individually
Feature
- #44297 : Monitor internal system memory (stack) and warn when limit reached
- #44988 : Increased precision of shot timestamps
- #45646 : Expand the SystemCheck interface with parameters for different limits at the various production stages
Task
- #43763 : Increase production test limits to support larger range of phototransistor binnings
- #44063 : HS10G3 / LS10G3: Light Signal ServiceInteraction Extensions for SingleLane use
- #45795 : ShotDetected events have correct ISO8601 TimeStamps including timezone
Version 2026.1.3
Bug
- #44561 : Fix a possible crash on fast firing
Version 2026.1.1
Bug
- #43760 : Laserscore10m: Fixes a bug where no shots were registered while using Light Signal Exercises and the Range Control Station
Version 2026.1.0
Bug
- #43339 : AcousticDetectionSystems can block when too many potential shots registered within 10s
Feature
- #16166 : Persist coredump after crash
- #42543 : AcousticDetectionSystems: SignalAnalyzer always triggered with TimeDifferenceRecorder
- #43280 : EmergencyStopButtonTest uses new UserInteractiveSystemCheck protocol
- #43284 : LS10 SystemChecks use new UserInteractiveSystemCheck protocol
Task
- #38851 : Modify format and complete raw data (Themelia)
- #38959 : New shot raw data format for debug purposes
- #39366 : Improved detection and warnings in case of many broken or covered light sensors
- #41637 : New interface for userinteractive System-Checks
- #42541 : AcousticDetectionSystems: add MeasurementsStartCount to Shot RawData
- #42542 : AcousticDetectionSystems subcomponent update (Master FPGA) to Version 1.8.0
- #42544 : DetectionSystems: unify shot logs
Version 2025.1.9
Bug
- #42058 : fix Movetest for production
Version 2025.1.5
Bug
- #39405 : Fix System-Checks abort behaviour
Version 2025.1.4
Bug
- #40300 : Fix devices's connection status after update
Version 2025.1.0
Bug
- #36936 : Fix incorrect MQTT subscriptions in case of unconfigured device
- #37974 : Prevent invalid RangeSetting format in certain situations
Feature
- #34602 : Increase transmission security of important network messages
- #34688 : Better logging during device startup and bad network connection
- #35677 : Standard storage time of shot data on server increased to 2 weeks
Task
- #32359 : Log all Production DIDRom modifications
- #38260 : Extended version logging + uniform version query added
Version 2.8.9
Bug
- #42869 : Fix inhouse production test: DynamicSensorMeasurementTest
Version 2.8.8
Task
- #42522 : StaticSensorMeasurementTest: adjust measure levels
Version 2.8.5
Task
- #39609 : Improve inhouse production tests
Version 2.8.4
Task
- #38417 : Improve inhouse production tests
Version 2.8.3
Bug
- #39370 : Fix lightsignal change problems on large ranges
Version 2.8.1
Bug
- #37344 : Error blink codes are not output via Wink/Error LED
Task
- #38682 : Support newest Hardware Revisions RT10G3R1 and RT10G3-UMBS-R1
Version 2.8.0
Bug
- #35879 : Improved robustness of communication lines against interference
- #36844 : Fix logs containing large JSON documents
Feature
- #34687 : Publish ErrorMessage when MinionStateMachine is in Error State
- #34961 : More characters (18) in hostname to identify the device
Task
- #19999 : Add inhouse production test (PIO Test)
- #33054 : Modify inhouse production test (FpgaImageTest UserInteractive)
- #36127 : Fix production test for devices with alternative comparators (SawtoothLinearityTest)
- #36256 : Supported operation in Running-Target (RT10G3)
- #36766 : Accepting larger tolerances of hardware components
Version 2.7.1
Bug
- #35676 : Ensure that too much shot data cannot cause memory issues for the servers
Feature
- #35680 : Dual- / Tunnel- / PortableShotsensor: briefly flash Wink/Error LED when shot detected
Version 2.7.0
Task
- #32615 : Extend published shots with the measurement system's "Reference Kind"
Version 2.6.23
Bug
- #29159 : Increase the reliability of sensor read in general and specially during sawtooth adjustment, to avoid failed adjustments due to disturbed communication lines
Version 2.6.21
Bug
- #35766 : Fix Sawtooth-Adjustments during inhouse production tests
Version 2.6.18
Bug
- #34112 : Fix software crashes on defective hardware
Task
- #34307 : Add ServiceState "Configuration" to ShotDetection Library for MouningRefKind
Version 2.6.15
Bug
- #33803 : Fix inhouse production test (SpiCommunicationTest)
Version 2.6.13
Bug
- #33570 : Fix robustness of inhouse production test (TransmitterCurrentAdjustment)
- #33571 : Fix error 302 (MaxMqttSubscriptionsTooSmall)
Version 2.6.12
Bug
- #29662 : Fix onboard communication after update or processor reset
- #33355 : Adjust tolerances for inhouse production test (TransmitterCurrentAdjustment)
Version 2.6.10
Bug
- #32997 : Improved adaptation to ambient light
- #33000 : SensorDataAnalysis was displaying inconsistent data in rare situations
- #33039 : Improved behavior in case of polluted measuring system
- #33073 : Fix inhouse product test (StaticSensorMeasurementTest)
Feature
- #33156 : Fully support role based connection message (requestable)
Task
- #33053 : Add inhouse production test (TransmitterCurrentAdjustmentTest)
Version 2.6.9
Bug
- #32973 : Fix inhouse product test data (SawtoothLinearityTest)
Version 2.6.8
Bug
- #32956 : Fix inhouse product test tolerances (SawtoothIntegrationSpeedTest)
Version 2.6.4
Bug
- #32776 : Show warning in HealthCheck when something is in the target
Version 2.6.3
Bug
- #32616 : LabView (debug) interface to read adjustment values fixed
- #32675 : Adjustment fail conditions adapted
- #32687 : Adjustment values were sometimes poor before first exercise
- #32689 : Better logging of received lightsignal changes
Version 2.6.0
Bug
- #28530 : More robust behavior in poor network environments
- #30641 : Correct behaviour when ProductionCurrentAdjustment System-Check is badly adjusted
Task
- #28730 : Extend published shots with the measurement system's "Reference Kind"
- #29366 : Possibility to filter log messages for the Role e.g. Lane
- #29612 : Unified processor reset
- #30565 : Use distinct hostnames for all devices
- #31630 : Notify other devices after device connects / reconnects to STYX Rack
- #31751 : TargetChangers: TargetPictures can be assigned to Slots from RangeSettings
- #31998 : FactoryReset command from RangeSettings adapted to siuscode 3.3.0 (breaking change)
Version 2.5.2
Task
- #30550 : ProductionTest adjustments
Version 2.5.1
Task
- #30194 : Fix Production System-Check: SensorFunctionTest
Version 2.5.0
Task
- #29330 : New method to publish System-Check results to themelia server
Version 2.4.6
Task
- #28844 : STYX Time Analysis supports mqtt, tcp and udp as protocols
Version 2.4.5
Bug
- #29383 : ProductSettings always complete and without arbitrary FactoryResets
Version 2.4.0
Feature
- #25069 : Devices react to a Range Log Level changes
Version 2.3.7
Task
- #26688 : Fix SmartMic Production Test criteria
Version 2.3.3
Bug
- #25711 : Internal Hotfix (External Didrom access fixed)
Version 2.3.0
Feature
- #18058 : Device can become operational without connection to the STYX rack
Version 2.2.1
Bug
- #18180 : Acoustic Eye System Check fix for Production
- #18192 : Meteo Sensor field test parameters increased to sensor limit values
- #18193 : Acoustic temperature field test parameters increased to sensor limit values
- #18195 : Target Effect Generator field test parameters increased to sensor limit values
Version 2.2.0
Task
- #14480 : Improved notification when all subtests of a test group are finished. Improved progress status for test groups.